Run a finger along the underside of your cooker hood. If it comes away sticky, the filter above it is probably clogged with months of cooking grease. Most people never look at it, which is why so many extractors end up loud, weak and smelling of last week’s dinner. The good news is that it takes about twenty minutes to clean a cooker hood filter properly, and most of that is just waiting while it soaks.
Why you should clean a cooker hood filter
Every time you fry, roast or boil, the hood pulls steam and tiny drops of fat through the filter. The filter traps the grease so it does not end up in the fan or the ducting. Once it is clogged, air cannot get through, so the extractor works harder, gets noisier and clears less steam. In winter, that steam turns into condensation on the kitchen walls and windows. A saturated filter is also a fire risk if a pan flares up underneath it.
Check which filter you have
Metal mesh or baffle filters are the most common. They are washable and can be cleaned again and again.
Charcoal or carbon filters are found in hoods that recirculate air back into the kitchen instead of venting outside. These cannot be washed. They need replacing, usually every few months, depending on how much you cook.
Some hoods have both, with the metal one underneath and the charcoal one behind it.
What you need
- a sink, washing-up bowl or bath big enough for the filter
- very hot water, from the kettle if needed
- washing-up liquid
- bicarbonate of soda
- a soft brush or a non-scratch sponge
- rubber gloves
How to clean a cooker hood filter
1. Turn it off and let it cool
Make sure the hob and the hood are switched off and cold. If you can, switch the hood off at the wall too.
2. Remove the filter
Most metal filters unclip with a small latch or tab. Support them with one hand as you release them, because they can drop suddenly and they are often dirtier than you expect.
3. Soak in hot water
Fill the sink with the hottest water you can, add a good squirt of washing-up liquid and a few spoonfuls of bicarbonate of soda, and stir. Lay the filter in so it is fully covered and leave it for fifteen to twenty minutes. You will see the grease start to lift.
4. Brush gently
Use the soft brush to work the loosened grease out of the mesh, going with the direction of the slats. Do not use a wire brush, which can tear fine mesh. If it is still sticky, drain the sink and repeat the soak with fresh hot water.
5. Rinse and dry fully
Rinse with hot water and leave the filter to dry completely before putting it back. A damp filter will catch dust and grease even faster.
Can a cooker hood filter go in the dishwasher?
Many metal mesh filters can, and it is an easy way to keep them clean. Check the manual first, and put the filter on the bottom rack on its own on a hot cycle. Aluminium filters can darken in the dishwasher. It does not affect how they work, but they will not look shiny again.
Do not forget the hood itself
While you clean a cooker hood filter, wipe the hood itself too. Wipe the underside, the edges and the controls with warm soapy water. For stainless steel, follow the grain and dry it with a soft cloth so it does not streak. The fan area behind the filter can be wiped carefully if you can reach it safely.
How often to clean it
If you cook most days, clean a metal filter once a month. If you fry a lot, every couple of weeks is better. Replace charcoal filters as the manufacturer suggests, usually every three to six months.
Part of a properly clean kitchen
In a small London kitchen, where cooking steam has nowhere to go, the cooker hood works hard. It is also one of the jobs that gets missed in a weekly clean, along with the oven, the tops of cupboards and the tiles behind the hob. A professional deep cleaning covers all of them, and the hood and filter are always checked during an end of tenancy cleaning in London, because inventory clerks look for grease there first.
Between deep cleans, make it a monthly habit. It takes twenty minutes to clean a cooker hood filter, and your kitchen will smell fresher and stay drier for it.
Cooker hood filter questions
What is the easiest way to clean a cooker hood filter?
Soak a metal filter for fifteen to twenty minutes in very hot water with washing-up liquid and a few spoonfuls of bicarbonate of soda, then brush it gently, rinse and let it dry fully.
Can I put my extractor fan filter in the dishwasher?
Most metal mesh filters can go in the dishwasher on a hot cycle, on the bottom rack. Check the manual first. Aluminium filters may darken, but they will still work. Charcoal filters should never be washed.
How often should I clean my cooker hood filter?
About once a month if you cook most days, and every couple of weeks if you fry often. Charcoal filters need replacing every three to six months.
Can you clean a charcoal cooker hood filter?
No. Charcoal filters absorb smells and stop working once they are full. Washing them does not restore them, so they need replacing.
Why is my extractor fan not sucking properly?
The most common reason is a clogged filter. Cleaning or replacing it usually restores the airflow. If it is still weak after that, the ducting or fan may need checking.
